Social Feed

Sharing my first 120P aquarium and hoping to obtain feedback and guidance as it progresses.

I purchased the ADA 120P tank, AFA stand, mat and ADA substrate set from AFA in San Francisco. The set cost approx $2,000 including shipping. The set arrived as a set of boxes on a pallet which was loaded into my garage by a local delivery service using a small fork lift. The delivery process took approximately 4 weeks.

The substrate set included one large bag of ADA power sand, the three ADA additives - bacter 100, tourmaline and super clear, five bags of Amazonia 2 regular, and two bags of Amazonia 2 powder.

The tank is 120 x 50 x 50 cm, so roughly 48” x 20” x 20” and holds approximately 80 gallons.

All items arrived in excellent condition. Helpers and I moved the items to the basement. The stand was easy to put together. Plywood based. Sturdy. I drilled some additional 4” holes in the left side and rear panels for access. I put down the mat, and added the tank.

I chose a chihiros 1200 wrgb2 pro light. I hung an IKEA adjustable rod holder over the tank to suspend the light from which has been working out well for my tanks.

For other mechanicals: these have evolved since initial setup

• Oase BIomaseter 2 thermo 350 canister filter loaded up with seachem matrix, seachem matrix carbon and seachem purigen.
• Cuboid aquatics UV disinfection unit.
• Oase Biomaster 2 850 canister filter loaded up similar to 350 and with all pre filter stuff (outer housing, center pipe, pads) removed
• Netlea pre filter
• ARC small acrylic yugang horizontal reactor
• five pound co2 tank
• CO2 Art pro CO2 regulator
• soft, gray silicone 16/22 hosing used throughout
• two sets of quick disconnects for the hosing
• Jardli glass Lily pipe outlets
• Hydra aquatics stainless steel inflow with skimmer
• some inexpensive motion sensing led panels for light within the cabinet
• two kasa smart plug strips

I’ve attempted to include some photos here but they don’t seem to be being pulled in.




The hardscape for the tank was selected collaboratively with the team at cuboid aquatics in Pipersville, PA. I became aware they carried a wide range of hardscape including the WIO product line and they were within driving distance (6 hours), so I drove down and spent the next day with them. They were well stocked and were incredible people! Their lead designer Maddie lead the effort. The design uses large WIO black venom and jade rocks to support a hefty set of Galapagos and WIO Centurian wood. I packed up the hardscape, brought it home and put together the current design. I chose the larger Galapagos pieces as I liked the dark highly contoured lines.

The design is a triangular layout as the tank will be viewed from the right side as well as the front and we wanted to keep that right side looking similar to the front.

The left side and rear are filled with the ADA substrate set. In two areas just in front of hardscape there are areas of substrate set where I intend to plant dwarf lilies and crypt spiralis tiger. The remainder of the front and right side uses WIO Everglades riverbed which includes tan sand, pebbles, twigs, leaves, and cones. I also added WIO black venom and jade pebbles and twigs.

My friend and I primarily used seachem epoxy to epoxy the hardscape together. It was easy to use. It does put off quite an odor. We also used a glue product call R6000 which seems to have worked out quite well. The tank has been in water for two weeks now. Some of the putty connected to wood has come loose. Best I can tell the R6000 joints are holding.



This is the current layout and you can see there is the normal whiteish “stuff” growing on some of the driftwood.

My friend and I filled the tank and started up the equipment to check for leaks and flow. We encountered a few small issues that were quickly resolved.

In 1-2 hours it was obvious there were loads of tannins in the water. I had read an article on cycling on 2hr that suggested turning off the equipment, letting the hardscape soak for 48 hours, draining, refilling and restarting, so this is what I did.

Once I had that new water……

Oh, water here comes from RO water normally remineralized with APT Sky up to a TDS of 100-120, however I had read that it’s best to make sure.KH is present to support the cycling process so this water was remineralized with APT Sky plus to a KH of 2-3.

To help boost the cycling process I started with Microbe-lift gel filter inoculation in both canisters, and Microbe-lift Nite-out and special blend products.

Water tests show that two weeks in I have high ammonia and nitrite. Tank is running with no light.

I did start up the co2 reactor as I’ve never used the horizontal yugang reactor and wanted to see what sort of co2 levels I could reach. I measured 40-50 ppm with the Hanna test set which is great and turned the co2 back off for now.

I will continue to monitor ammonia and nitrite near daily.

In the mean time I will be working on a planting plan.

Please get back to me with any comments, suggestions for sustainability, improvement, etc.

CO2 injected 1.4 pH drop (50 ppm per Hanna test)
Light 50-60 par at substrate
PPS-pro ferts for high tech tanks
50% water change weekly
8 dgH
0-1 dkH

Had a tree fall on the house last night and there's a chunk of drywall that ended up in the tank. Currently triage has electrical service restoration above addressing the tank. I can't easily get it out because there's debris on the lid (and the whole kitchen). What are the thoughts? I can likely get it siphoned out in a couple hours (been about 5 hours since the tree fell). Unsure I'll be able to do a full water change as the water won't be heated. Generator and battery backups will be started after tree cleanup. The tank itself is on a 2kwh battery, so full run time is 12ish hours.

Trying not to freak out and hope the fish will be okay.

Thanks!

Sounds like a joke question but for reasons unknown I cant get moss to grow period, Got a huge baseball of moss for free from shrimp breeder. I put some in 5g shrimp tank, low light no heater around 74 its dead. 3 other tanks 76 degree low to medium light its all dead or looks dead its grey color I'd say it's dead. water parms are pretty spot on no big shifts or other plants would have issues imo.

what do I need to do to grow java moss ? grew it for years no issues would take over now im lost! I can grow anything but moss?

I've seen several in the community mention purchasing an Archaea cabinet. I just recently purchased the 60x45 "Assembly Required" version in the Driftwood color and assembled it yesterday evening. It went together quite quickly without even downloading the instructions. I gotta say, I think it's absolutely a good option, if you're not wanting to build a cabinet yourself, but gag at the high cost of other aquarium cabinets sold by the high-end tank brands. I considered the slightly more expensive pre-built model, but it's cost doesn't include the freight shipping. Since this will be going in my living room, I didn't want to take chances on my own build and finishing skill. I think I made the right choice.

Archaea Modern-Nature Aquarium Cabinet

It will be tough to get away, but I have managed to finagle enough coverage for the weekend, so I did it! I have my ticket! I figure why not? It’s actually not that far from me. Daichi Araki from ADA is teaching an aquascaping masterclass on Saturday morning. Also interested in the ADA Shizuku workshop.



Juris Jutjajevs previously announced he will be attending the Jersey show.

I have never been to an Aquashella, so don’t entirely know what to expect, but I presume it is much like any large convention exhibit hall experience. Any ‘Crunchers thinking of attending the Jersey show?

There is A LOT of history to this that is tied to some of the biggest names in the hobby's past. I tried to get them into the USA with Clause Christensen back in the 90s but no-go.

This would be big news for US hobbyists as availability of healthy, aquarium-ready plants is THE limiting factor in expanding the hobby in the USA.

Welcome to ScapeCrunch, @Dwillydog!
We would love to get to know you. Please tell us about yourself. What tank do you have?

Hey guys, I've made a couple of yugang reactors some horizontal, some vertical (soda bottle with a hole in it).

I've noticed a reoccuring issue constantly in that it will eventually fill up with air (oxygen) from plants pearling.

Once the co2 + oxygen concentration gets high enough, Oxygen from plant pearling will eventually make its way into the reactor. After a few days, this severely reduces its efficiency.

You would think the oxygen just gets pushed out by the co2 coming, but plants pearling will kinda just refill it up extremely fast.

Is yugang better in lower light tanks where you won't get intense pearling? I usually find co2 misting much more consistent in this case and might swap back to just using a ceramic diffuser for consistency. I only have 10 gallon tanks... a ceramic diffuser is fine, its just easy to nuke your tank with too much co2 where yugang limits your co2 ppm based on reactor size.

We often talk about how fragile glass lily pipes are. I've only broken two of those, but today I broke my 4th (at least) drop checker. Maybe I need to start handling them more carefully like my lily pipes. It doesn't help when you're cleaning them over a granite counter top.