Social Feed

This is my first time using a reactor. I have a Landen 100p (40x18x18 inches) and just received my Aqua Rocks Colorado Stainless Yugang Reactor. I had a spare Eheim 4+ 350 so it's now hooked to that with just foam filtration. My other filter is an Oase Biomaster Thermo 600 with an 850 head. I'm a little confused on the initial setup. I have my Co2 turning on at 9:30am, lights on 12-8pm. I have the offsets at 50% of the reactor, and the surface area is 4 inches larger than the calculations said I needed.

I know that contact time is the factor so my Eheim is about 50% flow. Do I initially increase the Co2 rate to purge the air out of the reactor, then dial it back so i'm seeing off-gassing every minute once I'm reaching my ppm? I'm using a Co2 Art Elite Pro regulator. My psi sits between 35-40 on a 20lb tank. Co2 is easy for me to get and cheap so I'm not concerned with excess. There's not a lot of information I can find on these so anything helps. Thanks for reading!

Hi guys!

I'm new here, but not entirely new to planted tanks though I've been out of the hobby for the better part of the last decade between kids and moving a couple of times - but finally in a spot where I can do something again. I'm mostly going to be making things up as I go along, but plan on a lot of automation (I want to integrate everything into home assistant) and a lot of DIY as I love the challenge of building things out myself.

The starting point:

I picked up a 90P rimless, low-iron tank on a great deal.



I have a rough idea in my head for a stand to be built from plywood - just have a couple other house projects to finish off before starting that built.

Wife says I can only have one aquarium, so for this tank, I want to go all out with a sump to allow for auto top off, and auto water changes, auto fertilizer dosing etc. etc. I have half a plan in my mind.

I've also started on the light fixture which I've modeled up in CAD, and plan on making out of an 8020 extrusion, and some 3D printed bits.

I'm using bridgelux gen 3 thrive CW (3000k) and WW (5000k) LED strips which have super high CRI at 98+ along with some specific XPE2 wavelengths that I'll solder onto some starboards. Far Red (730nm), Red (654nm), Cyan (495nm), Blue (455nm), Visible UV (415nm). Each segment of the white channels will be on its own driver so I can adjust left to right brightness in thirds, and each colour channel on its own driver so I can vary each channel on a time-based approach.

These will be run from a custom PCB board with Meanwell N-LDD drivers, and will run ESPHome on an ESP32 so it can link up with my Home Assistant installation.


That's it for now, this will probably be a very slow build so be warned if you follow along!

So I've somehow used up my gallon of metricide for excel, now I think you need a business license to purchase it on amazon.

I want to go back and try hydrogen peroxide again since its so easy and cheap to buy.

What ratios are you guys using to get rid of algae on plants such as BBA that are still somewhat safe for more delicate mosses?
Or should the mosses just be avoided for this?

1/2 peroxide + 1/2 water into a spray bottle for treating outside the tank?

Finally a journal.

I’ll soon be setting up two new tanks, a UNS 90p and a 50c. (Not so!) Patiently awaiting tanks and stands delivery.

They will both be middle energy tanks. I have lengthy periods of busy time and travel that mean the tanks need to survive without human intervention here and there. So plenty of automation is needed, and slow and steady wins over high energy. Or in BBQ smoking terms: low and slow.

Plans:

• Injected CO2, but less than 30ppm
• Inert gravel
• Tidal HOB filter and partial UGF plate.
• Less than EI ferts, but more than PPS pro.
• Tap water (my tap is 50 TDS and only 10ppm Ca) remineralized to 30ppm Ca and 3-4 dKH.
• Lower light levels: Week aqua L on 90p and Chihiros wrgb 2 slim on 50c.
• Easy slow growing plants, and a few fish. Thinking the 50c will be a shrimp tank.
• Some hardscape but nothing crazy

My last tank has had a rough year. Hurricane Helene meant two weeks with no electricity, and much longer without decent water changes.

Then last summer the tank developed a slow leak while I was out of town (ugh!). Had to fly home for a week to triage. Fish and plants have been in temporary tanks. Plants are struggling. Photo is when they had already been in temporary bin for over 6 weeks, I was surprised it didn’t look like an algae infested swamp.





Sooo ready for my new tanks! These are my first really nice tanks, I’ve only owned petco specials before.

For the new tanks I'm planning on over ordering plants since my surviving plants are clearly pretty weak at this point.

It will be tough to get away, but I have managed to finagle enough coverage for the weekend, so I did it! I have my ticket! I figure why not? It’s actually not that far from me. Daichi Araki from ADA is teaching an aquascaping masterclass on Saturday morning. Also interested in the ADA Shizuku workshop.



Juris Jutjajevs previously announced he will be attending the Jersey show.

I have never been to an Aquashella, so don’t entirely know what to expect, but I presume it is much like any large convention exhibit hall experience. Any ‘Crunchers thinking of attending the Jersey show?

I'm doing it again! I will be trying AR mini and another type of AR and I always stunt them. I was doing some light reading as I already know AR hates the soup I serve.

So, is there any truth in K dosing exceeding total Ca causes boron lock out in AR types?

Welcome to ScapeCrunch, @Sergey_PAT!
We would love to get to know you. Please tell us about yourself. What tank do you have?